Your Complete Instruction for Installing a Bathtub
Your Complete Instruction for Installing a Bathtub
Blog Article
The article down below relating to Tools You Need to Install a New Bathtub is without a doubt compelling. Check it out for your own benefit and figure out what you think about it.
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a moderately difficult task. If the old bathtub is easily accessible, the job can relocate speedily; if you have to open a wall surface to remove the old tub and also position the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as set in the new one. See to it you have qualified yourself for the task as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you set up a new bathtub in your bathroom if you have actually already purchased a brand-new bathtub and also don't require to transform the arrangement of your previous supply of water pipelines.
Your tools and material checklist must make up the following:
Planning for the Installation
To start with, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its last placement.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be fairly problematic due to the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will come from the pipelines. When the supply pipes have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bathtub in the needed placement. The wood boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bath tub until the spirit level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water as well as examine all joints and new pipework for leakages as well as tighten them if essential. Load the tub and also inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the maker's user's manual. Tiling and sealing around the tub must wait until the tub has actually been utilized at least when as this will resolve it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washing machines are in location between the tap and the sink. Protect the tap in place with the manufacturer given backnut. When the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap ports. The previous type must be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack an inflexible seal, causing the water to permeate the wall between the bath as well as the tiling, bring about complications with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes and cartridges, as well as are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealer can fracture rather very early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about A Step-by-Step Guide to Installing a Bathtub? Leave a remark down the page. We will be interested to hear your reactions about this page. Hoping that you visit us again later on. You should take a moment to promote this blog if you liked it. Thanks so much for going through it.
Apply Now Report this page